BIOS passwords are used to add some extra security to computers. You can either set a password to prevent access to BIOS settings or to prevent PC from booting.
But sometimes this extra security might become a pain when you forget the BIOS password or someone changes your system BIOS password intentionally.
But there is no need to worry. There are many known ways to reset / remove / bypass the password:
- By removing CMOS battery
- By using motherboard jumper
- By using MS DOS command
- By using software
- By using Backdoor BIOS password
Now I'll try to explain each method one by one:
DISCLAIMER: This information is intended for experienced users. It is not intended for basic users, hackers, or computer thieves. Please do not try any of following procedures if you are not familiar with computer hardware. We'll not be responsible for the use or misuse of this information, including personal injury, loss of data or hardware damage. So use it at your own risk.
By Removing CMOS Battery:
Almost all motherboards use a small coin sized CMOS battery to store all BIOS settings along with the password. To reset the password, unplug the PC, open the cabinet and remove the CMOS battery for approx. 15-30 minutes and then put it back. It'll reset all BIOS settings as well as the password and you'll need to re-enter all settings.
If it fails, then try to remove the battery for at least one hour.
By Using Motherboard Jumper:
Almost all motherboards contain a jumper that can clear all CMOS settings along with the BIOS password. The location of this jumper varies depending upon the motherboard brand. You should read your motherboard manual to check its location. If you don't have the manual then look for the jumpers near the CMOS battery. Most of the manufacturer label the jumper as CLR, CLEAR, CLEAR CMOS, etc.
When you find the jumper, look carefully. There will be 3 pins and the jumper will be joining the center pin to either left or right pin. What you need to do, is remove the jumper and join the center pin to the opposite pin. e.g. if the jumper joins center pin to left pin, then remove it and join center pin to right pin. Now wait for a few seconds and then again remove the jumper and join the center pin to left pin.
Make sure to turn the PC off before opening the cabinet and resetting the jumper.
By Using MS DOS Command:
This method works only if you have access to the system when its turned on because this method requires MS DOS. Open Command Prompt from Programs menu and provide following commands one bye one:
debug
o 70 2E
o 71 FF
quit
NOTE: The first character in the above commands is English alphabet "o" and not the number 0.
After providing the above commands, restart your system and it should reset the CMOS Settings along with the BIOS password.
If you are curious to know how it works? then let me explain the above commands:
In this method we are using the Debug tool of MS DOS. The "o" character present at first in these commands, outputs the values to IO ports. The number 70 and 71 are port numbers which are used to access CMOS memory. By providing FF value we are telling CMOS that there is an invalid checksum and it resets the CMOS settings as well as BIOS password.
By Using Software:
There are a few software which can also reset CMOS settings or BIOS password or both within a few clicks. But as stated above you should have access to a system which is turned on and should have access to MS DOS or MS Windows:
By Using Backdoor BIOS Password:
Some BIOS manufacturer put a backdoor password in BIOS which always works irrespective of what password you have set in BIOS. Its a master password which is used for testing and troubleshooting purposes.
AMI BIOS Passwords:
A.M.I.
AAAMMMIII
AMI?SW
AMI_SW
AMI
BIOS
CONDO
HEWITT RAND
LKWPETER
MI
Oder
PASSWORD
AWARD BIOS Passwords:
01322222
589589
589721
595595
598598
ALFAROME
ALLy
aLLy
aLLY
ALLY
aPAf
_award
award
AWARD_SW
AWARD?SW
AWARD SW
AWARD PW
AWKWARD
awkward
BIOSTAR
CONCAT
CONDO
Condo
d8on
djonet
HLT
J64
J256
J262
j332
j322
KDD
Lkwpeter
LKWPETER
PINT
pint
SER
SKY_FOX
SYXZ
syxz
shift + syxz
TTPTHA
ZAAADA
ZBAAACA
ZJAAADC
PHOENIX BIOS Passwords:
BIOS
CMOS
phoenix
PHOENIX
Misc Common Passwords:
ALFAROME
BIOSTAR
biostar
biosstar
CMOS
cmos
LKWPETER
lkwpeter
setup
SETUP
Syxz
Wodj
Other Manufacturer BIOS Passwords:
Biostar - Biostar
Compaq - Compaq
Dell - Dell
Enox - xo11nE
Epox - central
Freetech - Posterie
IWill - iwill
Jetway - spooml
Packard Bell - bell9
QDI - QDI
Siemens - SKY_FOX
TMC - BIGO
Toshiba - Toshiba
VOBIS & IBM - merlin
NOTE: All these passwords are case-sensitive and are changed from time to time by manufacturers.
This article was posted by VG in following section: Troubleshooting, Windows 7, Windows Vista, Windows XP.
If you enjoyed this article, subscribe to our RSS feed or free newsletter to get all new articles directly in your Inbox. Also check out our popular articles and archive to read other interesting articles.
tony
toshiba satellite m505 i need in removing the password from bios in this laptop model
charlie
Hey having Problem here with my PC!!!
Someone playin with the BIOS and creat a password
can you help me remove the password ???
virbhadra
this site is very help for me
thanks
a want to talk with you
pls give me your face book or yahoo id
and
to chat with me one times
ons more
thanks
ankit
DEAR RESPECTED
SIR
I WOULD LIKE TO ENLIGHTEN ON THAT COMMAND PROMPT
THAT IT'S NOT POSSIBLE TO USE MS DOS WHEN COMPUTER STARTS
SO I'M SORRY BUT YOU'RE FAILED AT THIS POINT
VG
^^ The BIOS password is almost always set when you access BIOS settings and now when you start system. So you can easily boot into Windows and access Command Prompt.
saleem
servic tag :631m12s-595b
but i gut one cod :qj845668
the is cod us for dell inspiron 1420 bios removing
but how to gut no idia
Habib
Thanks Friends
GOVIND KUMAR
sir, i want to know how to recover password of domain administrator without using any additional software
C J NOATIA
I got a major problem. I have a HCL XITE L 52 Notebook. Insyde H2O BIOS. Once i put a password to lock hdd. But later i cleared it. But it wasn't cleared fully i suppose. Bcoz every time i boot up it asks for password, a real pain in ass.
So, my question is "Is there any ways to reset / restore BIOS setting to default values?" should i open up my lappy ? Or it would be too risky ?
VG
^^ It seems you have set startup password in BIOS settings. If its asking for password when you switch on your laptop, you'll need to ask a technician to reset the BIOS settings by opening the laptop.
You can also try the default passwords given at the end of above topic.