How to Reset / Remove / Bypass a BIOS or CMOS Password?

=========================

DISCLAIMER: This information is intended for experienced users. It is not intended for basic users, hackers, or computer thieves. Please do not try any of following procedures if you are not familiar with computer hardware. I'll not be responsible for the use or misuse of this information, including personal injury, loss of data or hardware damage. So use it at your own risk.

=========================

BIOS passwords are used to add some extra security to computers. You can either set a password to prevent access to BIOS settings or to prevent PC from booting.

But sometimes this extra security might become a pain when you forget the BIOS password or someone changes your system BIOS password intentionally.

But there is no need to worry. There are many known ways to reset / remove / bypass the password:

By removing the CMOS battery
By using the motherboard jumper
By using MS DOS command
By using software
By using Backdoor BIOS password

Now I'll try to explain each method one by one:

A. By Removing the CMOS Battery:

Almost all motherboards use a small coin sized CMOS battery to store all BIOS settings along with the password. To reset the password, unplug the PC, open the cabinet and remove the CMOS battery for approx. 15-30 minutes and then put it back. It'll reset all BIOS settings as well as the password and you'll need to re-enter all settings.

If it fails, then try to remove the battery for at least one hour.

B. By Using the Motherboard Jumper:

In most motherboards CMOS battery is soldered, which makes it difficult to remove the battery. In this case we use another method.

Almost all motherboards contain a jumper that can clear all CMOS settings along with the BIOS password. The location of this jumper varies depending upon the motherboard brand. You should read your motherboard manual to check its location. If you don't have the manual then look for the jumpers near the CMOS battery. Most of the manufacturer label the jumper as CLR, CLEAR, CLEAR CMOS, etc.

When you find the jumper, look carefully. There will be 3 pins and the jumper will be joining the center pin to either left or right pin. What you need to do, is remove the jumper and join the center pin to the opposite pin. e.g. if the jumper joins center pin to left pin, then remove it and join center pin to right pin. Now wait for a few seconds and then again remove the jumper and join the center pin to left pin.

Make sure to turn the PC off before opening the cabinet and resetting the jumper.

C. By Using MS DOS Command:

This method works only if you have access to the system when its turned on because this method requires MS DOS. Open MS DOS from programs menu and provide following commands one bye one:

debug
o 70 2E
o 71 FF
quit

NOTE: The first character in the above commands is "O" and not the number 0.

After providing the above commands, restart your system and it should reset the CMOS Settings along with the BIOS password.

If you are curious to know how it works? then let me explain the above commands:

In this method we are using the Debug tool of MS DOS. The "O" character present at first in these commands, outputs the values to IO ports. The number 70 and 71 are port numbers which are used to access CMOS memory. By providing FF value we are telling CMOS that there is an invalid checksum and it resets the CMOS settings as well as BIOS password.

D. By Using Software:

There are a few software which can also reset CMOS settings or BIOS password or both within a few clicks. But as stated above you should have access to a system which is turned on and should have access to MS DOS or MS Windows:

KillCMOS

!BIOS

CmosPwd

E. By Using Backdoor BIOS Password:

Some BIOS manufacturer put a backdoor password in BIOS which always works irrespective of what password you have set in BIOS. Its a master password which is used for testing and troubleshooting purposes.

AMI BIOS Passwords:

A.M.I.
AAAMMMIII
AMI?SW
AMI_SW
AMI
BIOS
CONDO
HEWITT RAND
LKWPETER
MI
Oder
PASSWORD

AWARD BIOS Passwords:

01322222
589589
589721
595595
598598
ALFAROME
ALLy
aLLy
aLLY
ALLY
aPAf
_award
award
AWARD_SW
AWARD?SW
AWARD SW
AWARD PW
AWKWARD
awkward
BIOSTAR
CONCAT
CONDO
Condo
d8on
djonet
HLT
J64
J256
J262
j332
j322
KDD
Lkwpeter
LKWPETER
PINT
pint
SER
SKY_FOX
SYXZ
syxz
shift + syxz
TTPTHA
ZAAADA
ZBAAACA
ZJAAADC

PHOENIX BIOS Passwords:

BIOS
CMOS
phoenix
PHOENIX

Misc Common Passwords:

ALFAROME
BIOSTAR
biostar
biosstar
CMOS
cmos
LKWPETER
lkwpeter
setup
SETUP
Syxz
Wodj

Other Manufacturer BIOS Passwords:

Biostar - Biostar
Compaq - Compaq
Dell - Dell
Enox - xo11nE
Epox - central
Freetech - Posterie
IWill - iwill
Jetway - spooml
Packard Bell - bell9
QDI - QDI
Siemens - SKY_FOX
TMC - BIGO
Toshiba - Toshiba
VOBIS & IBM - merlin

NOTE: All these passwords are case-sensitive and are changed from time to time by manufacturers.

This article was posted in Others, Troubleshooting, Windows 7, Windows Vista, Windows XP.

Subscribe to RSS Feed | Email Newsletter | More Articles

42 Comments

Tapas manohari

1. Download the free tool MoveOnBoot
2. Open MoveOnBoot
3. Go to Rename Action -> Rename File
4. A dialog box will open, select the file. Since these virus files are hidden files , you won’t be able to browse and see it. Please enter enter “C:\protectfile.vbs” in select-file section.
5. Enter “C:\protectfile.html” in the destination file section. Enter OK.
6. Similarly repeat steps 2 to 4 for the file “C:\autorun.inf” and rename it to “C:\autorun.html”
7. Don’t restart your computer. We have set moveonboot to rename the ProtectFile.vbs in just one of the drives.
8. Repeat step 2 to 5 for each of the drives. For example if you have 4 drives in your computer(C, D, E, F), then you will have to rename “C:\protectfile.vbs”, “D:\protectfile.vbs”, “E:\protectfile.vbs” and “F:\protectfile.vbs” to “C:\protectfile.html”, “D:\protectfile.html”, “E:\protectfile.html” and “F:\protectfile.html” respectively. Similarly rename “autorun.inf” files in all the drives to corresponding “autorun.html” files.
9. Restart your computer. We have disabled the virus.
10. Now we will remove them completely.
11. Open MoveOnBoot again.
12. Go to Delete Actions -> Delete Files
13. You won’t be able to browse and reach the files. So click browse and enter “C:\protectfile.html”, “D:\protectfile.html”, “E:\protectfile.html” ,”F:\protectfile.html”, “C:\autorun.html”, “D:\autorun.html”, “E:\autorun.html” and “F:\autorun.html”
14. Restart your computer.
Abhishek

Hi Vishal,
nice to see informaion published. After lot of frustation on trying to unlock my Insyde BIOS F-36 modalled in Compaq Cq45-AU 106, want a peiece of useful info...

I made XP CD with SATA drivers using nlite etc.. but a blue screen is coming before asking the file system. my bios is locked and i am not able to get option to install XP. Can you please let me how to unlock BIOS to install XP.
Abhishek

Hi Vishal,
nice to see informaion published. After lot of frustation on trying to unlock my Insyde BIOS F-36 modalled in Compaq Cq45-AU 106, want a peiece of useful info...

I made XP CD with SATA drivers using nlite etc.. but a blue screen is coming before asking the file system. my bios is locked and i am not able to get option to install XP. Can you please let me how to unlock BIOS to install XP.
Sue

I am attemping the MS DOS, but I don't usually do the system setup. Can you explain step by step how to access MS DOS? I didn't see it in the system start up, in start menu, or through mozilla. Thanks
Sue

I tried the battery, it didn't work. I need help, lpz!
VG

^^ Try to access it using cmd command in RUN. Also it should be present under "Accessories" menu.
buboy

Hello! My name is Mr. IT1)I have a Dell Inspiron 1000 Laptop Please help i don't know what happen to my laptop. I was tried all possible password.
I was tried also the backdoor password but still the problem did not fixed.
2)any friend out there some idea on how to reset BIOS password please help me.

Thank you,
IT Boy
VG

^^ Did you try the MS DOS command mentioned in Point C and software mentioned in Point D?
Shailesh Microsoft

Hi...........

My name is shailesh

i want to set a unick bios password for my PC
& no one hardware engineer also change it.

I know some methad.....

1. By using Jumper setting on mainboard.

2. By removing CMOS Battery on mainboard.

3. By using MS-Dos command.

But I want that not any above method will that password.

so if U have any idea about that Plz Tell me.

Waiting for Ur Reply.........Heartly
cryptonyt

Good Day Vishal,
Having problem with my laptop Acer 4520 w/ PhoenixBios 4.0 Release 6.1. Can you help me what steps to do.. I'm lockin on @ startup requiring Password Entry to Start. I lost my password.. Please Help Me..

Thank you!